How to detect new hard disk attached without rebooting in Linux

Suppose you have added a new hard disk to your Linux OS running on any Virtual Environment which in my case is VMware workstation. Once added the  new  hard drive, generally the changes won’t reflect unless you reboot the Guest OS.

But what if you are in no position to reboot the Gues Linux OS?

In the below path you can find a list of host symlinks pointing to the iscsi device configured on your Linux box

# ls -l /sys/class/scsi_host/
total 0
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host0 -> ../../devices/pci0000:00/0000:00:07.1/host0/scsi_host/host0
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host1 -> ../../devices/pci0000:00/0000:00:07.1/host1/scsi_host/host1
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host10 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host10/scsi_host/host10
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host2 -> ../../devices/pci0000:00/0000:00:10.0/host2/scsi_host/host2
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host3 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host3/scsi_host/host3
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host4 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host4/scsi_host/host4
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host5 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host5/scsi_host/host5
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host6 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host6/scsi_host/host6
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host7 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host7/scsi_host/host7
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host8 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host8/scsi_host/host8
lrwxrwxrwx 1 root root 0 Jun 14 05:08 host9 -> ../../devices/pci0000:00/0000:00:11.0/0000:02:05.0/host9/scsi_host/host9

But to detect a new hard drive attached you need to first get your host bus number used which you can get by using below command
# grep mpt /sys/class/scsi_host/host?/proc_name
You should get a output like below
/sys/class/scsi_host/host2/proc_name:mptspi
So as you see your host2 is the relevant fiels where you need to reset the storage buffer values. Run the below command
# echo "- - -" > /sys/class/scsi_host/host2/scan
Here “- – -“ defines the three values stored inside host*/scan i.e. channel number, SCSI target ID, andLUN values. We are simply replacing the values with wild cards so that it can detect new changes attached to the Linux box. This procedure will add LUNs, but not remove them.

Once done verify if you can see the new hard drive which in my case worked very fine as I see below
# fdisk -l
Disk /dev/sdb: 3221 MB, 3221225472 bytes
255 heads, 63 sectors/track, 391 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Let me know your success and failures.

 

golinuxhub.com/2014/07/how-to-detect-new-hard-disk-attached.html